Omron FINS Error Codes
Error code (Decimal) |
Error code (Hex) |
Meaning |
---|---|---|
00 | 0x0 | No Error |
01 | 0x1 | Invalid Memory Address Parameter |
02 | 0x2 | Invalid or Illegal Command Param |
03 | 0x3 | Response SID did not match |
04 | 0x4 | NSB did not respond to send req |
05 | 0x5 | Timed Out - No Response |
06 | 0x6 | Timed Out Waiting For Response |
07 | 0x7 | Bad Received CRC |
08 | 0x8 | Unmatched Message IDs |
09 | 0x9 | Unmatched Command/Response |
10 | 0xa | Unknown Error |
11 | 0xb | Network Address Out Of Range |
12 | 0xc | Node Address Out Of Range |
13 | 0xd | Unit Address Out Of Range |
14 | 0xe | Invalid Address Parameter |
15 | 0xf | Timed Out waiting for echo |
16 | 0x10 | Bad Received FCS |
17 | 0x11 | Response from different Host Link Unit |
18 | 0x12 | No Valid Response Code |
19 | 0x13 | No FINS Response Packet |
20 | 0x14 | Unknown Error Code |
21 | 0x15 | Local Node not part of Network |
22 | 0x16 | Token Timeout, Node # too High |
23 | 0x17 | Number of Transmit Retries Exceeded |
24 | 0x18 | Max # of Frames Exceeded |
25 | 0x19 | Node # Setting Error |
26 | 0x1a | Node # Duplication Error |
27 | 0x1b | Dest Node not part of Network |
28 | 0x1c | No Node with Node # Specified |
29 | 0x1d | Third Node not part of Network |
30 | 0x1e | Busy Error, Dest Node Busy |
31 | 0x1f | Response Timeout, Noise or Watchdog |
32 | 0x20 | Error in Comm Controller |
33 | 0x21 | PLC Error in Dest Node |
35 | 0x23 | Undefined Command Used |
36 | 0x24 | Cannot Process Command |
37 | 0x25 | Routing Error |
38 | 0x26 | Command is too Long |
39 | 0x27 | Command is too Short |
40 | 0x28 | Specified Data Items != Actual |
41 | 0x29 | Incorrect Command Format |
42 | 0x2a | Incorrect Header |
43 | 0x2b | Memory Area Code Error |
44 | 0x2c | Access Size Specified is Wrong |
45 | 0x2d | First Address is Inaccessible |
46 | 0x2e | Address Range Exceeded |
47 | 0x2f | Unknown Error Code |
48 | 0x30 | Non-existent Program # Specified |
49 | 0x31 | Unknown Error Code |
50 | 0x32 | Unknown Error Code |
51 | 0x33 | Data Size in Command is Wrong |
52 | 0x34 | Unknown Error Code |
53 | 0x35 | Response Block too Long |
54 | 0x36 | Incorrect Parameter Code |
55 | 0x37 | Program Area Protected |
56 | 0x38 | Registered Table Error |
57 | 0x39 | Area Read-Only or Write Protected |
59 | 0x3b | Mode is Wrong |
60 | 0x3c | Mode is Wrong (Running) |
61 | 0x3d | PLC is in Program Mode |
62 | 0x3e | PLC is in Debug Mode |
63 | 0x3f | PLC is in Monitor Mode |
64 | 0x40 | PLC is in Run Mode |
65 | 0x41 | Specified Node is not Control Node |
66 | 0x42 | Specified Memory does not Exist |
67 | 0x43 | No Clock Exists |
68 | 0x44 | Data Link Table Error |
69 | 0x45 | Unit Error |
70 | 0x46 | Command Error |
71 | 0x47 | Destination Address Setting Error |
72 | 0x48 | No Routing Tables |
73 | 0x49 | Routing Table Error |
74 | 0x4a | Too Many Relays |
75 | 0x4b | The Header is not FINS |
76 | 0x4c | The Data Length is too Long |
77 | 0x4d | The Command is not Supported |
80 | 0x50 | Timed Out waiting for Port Semaphore |
94 | 0x5e | All Connections are in Use |
95 | 0x5f | The Specified Node is Already Connected |
96 | 0x60 | Attempt to Access Protected Node from Unspecified IP |
97 | 0x61 | The Client FINS Node Address is OOR |
98 | 0x62 | Same FINS Node Address is being used by Client and Server |
99 | 0x63 | No Node Addresses are Available to Allocate |